manualshive.com logo in svg

Lipco GSG-S-VM, Перевод оригинальной инструкции

Поделиться
Скачать
Lipco GSG-S-VM Скачать руководство пользователя страница 9

 

 

 

Instructions 

Saddle-mount unit GSG-S-VM 

 

   

 

 

9 - 72

 

 010710-03-EN BA GSG-S-VM / 13.07.2020

 

 

 

 
5.  General safety regulations 

 

The operation of mobile plant protection units is associated with cer-
tain risks. Therefore, you must comply with the following safety regu-
lations:  

 

•

 

Before operating the machine, always read the operating manual 
and comply with all safety instructions! 

 

•

 

Never remove or modify safety devices! 

 

•

 

Secure the area beneath the machine for repairs or inspections!  

 

•

 

Switch off the machine prior to performing maintenance or care! 

 

•

 

Always maintain safety clearances!  

 

•

 

Note! Do not enter the work area while the universal joint shat is 
rotating! There is an increased risk of accident in case of contact. 
For  your  safety,  do  not  wear  loose  clothing  or  accessories  (e.g. 
scarves)!  

 

•

 

Operate,  maintain  or  repair  the 

GSG-S-VM

  only  by  especially 

trained personnel who are aware of the risks involved! 

 

•

 

The operator is responsible for compliance  with applicable acci-
dent  prevention  regulations,  in  addition  to  the  generally  recog-
nized safety, occupational health and traffic safety regulations! 

 

•

 

The  warning  and  information  signs  on  the  machine  provide  im-
portant  information  for  safe  operation;  compliance  with  these 
warnings will increase your safety!

 

 

•

 

Persons not involved must keep out of the work area of the ma-
chine. 

 

•

 

Keep children away from the 

GSG-S-VM

 and spray. 

 

•

 

Operate machine only at the specified speed  
(max. 540 rpm)! 

 
 

 

Содержание GSG-S-VM









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды