manualshive.com logo in svg

Lika RD6 Series, Руководство пользователя

Поделиться
Скачать
Lika RD6 Series Скачать руководство пользователя страница 65

Position window [0x01]

[Register 2, Unsigned16, rw]
This parameter defines the tolerance window limits for the  

Target position

[0x2B-0x2C]

 value. As soon as the axis is within the tolerance window limits,

the bit 8 

Target position reached

 in the 

Status word [0x01]

 goes high (“=1”).

When the axis is within the tolerance window limits for the time set in the

Position window time [0x02]

  parameter, the  bit 0 

Axis in position

  in  the

Status word [0x01]

 goes high (“=1”). The parameter is expressed in pulses. See

also the “Positioning: position and speed control” section on page 43.
Default = 1 (min. = 0, max. = 65535)

Position window time [0x02]

[Register 3, Unsigned16, rw]
It represents the time for which the axis has to be within the tolerance window
limits set in the 

Position window [0x01]

 parameter before the state is signalled

through   the 

Axis   in   position

  status  bit   of   the  

Status   word   [0x01]

.   The

parameter is expressed in milliseconds. See also the “Positioning: position and
speed control” section on page 43.
Default = 0 (min. = 0, max. = 10000)

Max following error [0x03-0x04]

[Registers 4-5, Unsigned32, rw]
This parameter  defines the  maximum  allowable  difference  between  the  real
position and the theoretical position of the device. If the device detects a value
higher   than   the   one   set   in   this   parameter,   the  

Following   error

  alarm   is

triggered and the unit stops. The parameter is expressed in pulses.
Default = 50000 (min. = 0, max. = 1000000)

Kp position loop [0x05]

[Register 6, Unsigned16, rw]
This parameter contains the proportional gain used by the PI controller for the
position loop. The value has been optimized by Lika Electronic according to the
technical characteristics of the device.
Default = 80 (min. = 0, max. = 1000)

Ki position loop [0x06]

[Register 7, Unsigned16, rw]
This parameter  contains the  integral  gain  used  by  the  PI  controller  for the
position loop. The value has been optimized by Lika Electronic according to the
technical characteristics of the device.
Default = 10 (min. = 0, max. = 1000)

MAN RD6 MB E 1.1

Programming parameters

65 of 92

RD6 Modbus®

Содержание RD6 Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды