Lika CKP58 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 44

Lika CKP58 Скачать руководство пользователя страница 37

IP58, IQ58, IQ36

Max rpm

It allows to optimize the encoder performance (by keeping the most efficient
ratio between either the rotational speed and the precision in the case of the
IP58 encoder; or the rotational speed and the edge distance in the case of the
IQ58/IQ36 encoders), depending on the maximum speed the application is able
to reach. Since the maximum speed and the resolution are strictly correlated,
some options may be disabled or limited as you enter increasing resolutions. If
more options are available -

2250

;

4500

;

9000

for IP58 encoder;

xxxrpm(100

kHz)

;

xxxrpm (300 kHz)

;

xxxrpm (500 kHz)

for IQ58 and IQ36 encoders-, the

operator has to select the speed value option that is immediately higher than
the maximum speed of the application. If you do not know the maximum speed
the application is able to reach, please enter the maximum rotational speed
option available.

EXAMPLE

Let's assume that the resolution of an IP58 encoder is 1,024 PPR; in this case
three options are available for the operator to choose from:

2250

,

4500

and

9000

rpm. If the maximum speed of the application is 4,000 rpm, he has to

select the 4,500 rpm option; if the maximum speed of the application is 4,500
rpm, he has to select the 9,000 rpm option; if he does not know the maximum
speed of the application, then he has to select the 9,000 rpm option.

NOTE

Please note that the maximum counting frequency of an encoder, expressed in
kHz, results from the number of revolutions per minute (RPM) -i.e. its rotational
speed- and the number of pulses per revolution (PPR) -i.e. its resolution. It can
be calculated by using the following algorithm:

Maximum counting frequency (kHz)

=

RPM * PPR

60 * 1000

It follows that the higher the maximum rotational speed of the encoder and its
resolution, the higher the counting frequency. This has to be considered
carefully when you program the encoder, in particular referring to the maximum
counting frequency of the encoder as stated in the technical specifications, to
the following electronic equipment and to the length of the cables.

MAN IP58_IQ58_IQ36 E 1.6

Programming interface

37 / 44

«
...
35
36
37
38
39
...
»

Содержание CKP58













































Отзывы:

Нет отзывов