Lika CKP58 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 44

Lika CKP58 Скачать руководство пользователя страница 21

IP58, IQ58, IQ36

4.8 Index pulse setting input (IP-, CKP- models only)

NOTE

The Index pulse setting input is only available on IP-, CKP- models.

This   encoder   provides   the   zero   signal   (Index   pulse)   once   per   revolution   as
relative positioning reference (home position, see the Figure here above). In this
way a unique position can be identified at a well-known point in the 360°
revolution   of   the   encoder   shaft.   This   input   allows   to   set   the   point   in   the
revolution  at  which  the  0  pulse  will  be  output.  This function  is useful,  for
example,   when   you   want   the   zero   position   of   the   encoder   and   the   zero
mechanical position of the axis to match. When you want to set the position of
the 0 signal in the revolution you must send a  command via PLC or other
controller to the encoder through the dedicated input. Connect the Index pulse
setting input to 0Vdc if not used. To set the zero position, connect the Index
pulse setting input to +Vdc for 100 µs at least, then discVdc. Normally
voltage must be at 0Vdc. We suggest moving the axis to the desired position,
then   activate   the   Index   pulse   setting   function   while   the   encoder   and   the
mechanical assembly are in stop.

WARNING

Please check the position of the 0 pulse and set it if necessary whenever you set
a new resolution next to the

parameter or reverse the counting

direction.

NOTE

The width of the 0 pulse can be set next to the

Index length

parameter. Two

options are available:

90° el (gated A, B)

and

180° el (gated A)

. Please note

that the 0 pulse having a width of 90 electrical degrees is synchronised with A
and B pulses, while the 0 pulse having a width of 180 electrical degrees is
synchronised with A pulse. For further information please refer to page 35.

NOTE

It is possible to set the 0 pulse position also by either pressing the external
button located in the rear side of the encoder enclosure -see the “4.11 Index
pulse setting external button (Figure 1) (IP-, CKP- models only)” section on page
23 - this option is only available on IP-, CKP- models; or by means of the
programming interface -see the

Index position

parameter on page 35 - this

option is available on both IP- and IQ- series.

MAN IP58_IQ58_IQ36 E 1.6

Electrical connection

21 / 44

«
...
19
20
21
22
23
...
»

Содержание CKP58













































Отзывы:

Нет отзывов