LG STB-5500 Скачать руководство пользователя

Страница: 8 / 97

206-4310

STB-5500 Cabling Connections (Cont.)

Connect the STB to the Display Panel

This procedure only describes the essential STB/display panel connections. See Reference section,

“STB-5500 Jack Panels,” for further information on the additional jack panel ports and connectors.
1. Turn ON the display panel.
2. Refer to the STB-5500 Cabling diagram on page 10, and complete the following connections:

a) Make the appropriate Television/Display Control connection between the STB-5500 and the

display panel.

• For LG Hospitality TVs: Use the MPI/MTI cable provided to connect MPI/MTI TELEVISION

CONTROL on the STB-5500 front jack panel to the MPI port on the rear jack panel of the

display.

• For LG Public Display TVs or LG Commercial Monitors: Use the TLM cable provided to

connect RS-232C TELEVISION CONTROL on the STB-5500 rear jack panel to the DB9

RS-232 CONTROL connector on the rear jack panel of the display.

• For commercial non-LG TVs: Use the MPI/MTI cable provided to connect MPI/MTI

TELEVISION CONTROL on the STB-5500 front jack panel to the MTI (typically labeled

“DATA”) port on the rear jack panel of the display.

Note:

Commercial interfaces and their respective cables (MPI/MTI or TLM as specified above)

support IR pass-through.

b) Use the HDMI cable provided to connect HDMI OUT on the STB-5500 rear jack panel to the

HDMI1 input connector on the rear jack panel of the display.

Note:

When Television/Display Control communication is established, the STB default

configuration automatically sends Television/Display Control commands to switch the connected

display panel to its HDMI1 input.

c) For RF delivered content, connect a 75 ohm coaxial wire from the Antenna/CATV wall jack to

ANTENNA/CABLE IN on the STB-5500 rear jack panel. For IP delivered content, connect an

RJ-45 Ethernet (CAT5) cable from the institution’s network to the LAN port on the STB-5500

rear jack panel.

d) Insert the DC power plug of the AC/DC power adapter provided into the POWER connector

on the rear jack panel of the STB-5500, and then plug the AC/DC adapter into a standard

120V 60 Hz AC power outlet.
When power is applied to the STB-5500, the LED on the STB’s front jack panel will light

steadily, indicating that the STB is in standby mode. Also, the display panel will be turned

OFF by the STB as soon as the STB is powered and establishes Television/Display Control

communication with the display.

Note:

Once Television/Display Control communication is established between the STB-5500

and the display panel, the STB-5500 will be in control of the display panel, and certain resident

panel functions, like panel buttons, typically will no longer operate.

Note:

If connected to an LG Hospitality TV, the STB also will change several of the TV’s Installer

Menu settings in order to facilitate communication and functionality. See table following this

procedure for a listing of all Hospitality TV Installer Menu items that will be changed by the STB.

3. Use the Installer Remote to turn ON the STB/display panel.

(Continued on next page)

Содержание STB-5500


































































































Результаты поиска

Содержание STB-5500

Отзывы:

Похожие инструкции для STB-5500

Бренды по названию

Популярные бренды

LG STB-5500, Руководство по настройке коммерческого режима

Результаты поиска

Содержание STB-5500

Отзывы:

Похожие инструкции для STB-5500

Бренды по названию

Популярные бренды