LG STB-3000 Скачать руководство пользователя

Страница: 67 / 86

206-4272

Reference: Auto Input(s) Sensing Feature

This section provides detailed settings information for Installer Menu item 042 AUTO INPUTS.

Note:

When both item 042 AUTO INPUTS

and

item 041 SIMPLINK EN are enabled in the Installer Menu,

HDMI inputs will be detected by SIMPLINK, but the Auto Input(s) Sensing Feature will not function.
In the Installer Menu, an informational code is displayed at the right of each Auto Inputs value, for example:

STB_3000 PTC INSTALLER MENU

CPU-CTV

042 AUTO INPUTS 193 76XXXXX0

UPN 000-000-000-000

ASIC D279

PTC V1.00.023

CPU V3.00.71.01

Each code consists of eight characters that identify the Aux input(s) for which auto-sensing is enabled. The

following table identifies the Installer Menu display code Input # for each Aux input that is available on the

STB-3000. The table also identifies the Installer Menu item associated with each Aux input. Remember that

in order for auto-sensing to be enabled for an input, that input must also be enabled in the Installer Menu.

Installer Menu

Display Code

Input #

Aux

Input

Installer Menu

Item

Function

AV1

039

REAR AUX EN

HDMI 1

035

HDMI1 ENABLE

HDMI 2

091

HDMI2 ENABLE

To disable auto-sensing for all available Aux inputs, set item 042 to 0. To enable auto-sensing for all available

Aux inputs, set item 042 to 255. All other available settings (i.e., settings for individual inputs), are listed in the

table below.

Item 042

Value

Inputs

Installer Menu

Display

AV1

HDMI 1

HDMI 2

001

Enabled

Disabled

DDXXXXX0

064

Disabled

Enabled

Disabled

D6XXXXXD

065

Enabled

Disabled

D6XXXXX0

128

Disabled

Enabled

7DXXXXXD

129

Enabled

Disabled

Enabled

7DXXXXX0

192

Disabled

Enabled

76XXXXXD

193

Enabled

76XXXXX0

X = Aux input source is Disabled or Not Available (i.e., on this STB model)

D = Auto-sensing for input is Disabled

Input # = Auto-sensing for input is Enabled

AUTO INPUTS Display Code

This example illustrates Installer Menu item 042 value

193, which enables auto-sensing for all available Aux

inputs. The input #s in the display code (7, 6, 0 in this

example) identify the enabled Aux inputs. See first

table below for a listing of the STB-3000 Aux inputs

and their corresponding display code input #s. The

second table below shows the display codes for all

item 042 values.

Содержание STB-3000























































































Результаты поиска

Содержание STB-3000

Отзывы:

Похожие инструкции для STB-3000

Бренды по названию

Популярные бренды

LG STB-3000, Руководство по установке

Результаты поиска

Содержание STB-3000

Отзывы:

Похожие инструкции для STB-3000

Бренды по названию

Популярные бренды