LG MULTI V PLUS LRUC1008T1 Скачать руководство пользователя страница 29

Страница: 29 / 82

Installation Manual

Refrigerant piping installation

To Outdoor Unit

Capped Piping

1. Use the following materials for refrigeration piping.

• Material: Seamless phosphorous deoxidized copper pipe

2. Commercially available piping often contains dust and other materials. Always blow it clean with a

dry inert gas.

3. Use care to prevent dust, water or other contaminants from entering the piping during installation.

4. Reduce the number of bending portions as much as possible, and make bending radius as big as

possible.

5. Always use the branch piping set shown below, which are sold separately.

6. If the diameters of the branch piping of the designated refrigerant piping differs, use a pipe cutter to cut

the connecting section and then use an adapter for connecting different diameters to connect the piping.

7. Always observe the restrictions on the refrigerant piping (such as rated length, the difference between

high/low pressures and piping diameter).
Failure to do so can result in equipment failure or a decline in heating/cooling performance.

8. A second branch cannot be made after a header. (These are shown by

9. The Multi V will stop due to an abnormality like excessive or insufficient refrigerant. At such a time, always

properly charge the unit. When servicing, always check the notes concerning pipe length and amount of addi-
tional refrigerant at both locations.

. Never perform a pump down. This will not only damage the compressor but also deteriorate the per-

formance.

. Never use refrigerant to perform an air purge. Always evacuate using a vacuum pump.

12. Always insulate the piping properly. Insufficient insulation will result in a decline in heating/cooling perfor-

mance, water drops from condensation and other such problems.

13. When connecting the refrigerant piping, make sure the service valves of the Outdoor Unit is completely

closed (the factory setting) and do not operate it until the refrigerant piping for the Outdoor and Indoor Units
has been connected, a refrigerant leakage test has been performed and the evacuation process has been
completed.

14. Always use a non-oxidizing brazing material for brazing the parts. If a non-oxidizing brazing material is

used, it could cause clogging or damage to the compressor unit.

Caution

ARBL052S

ARBL102S

ARBL202S

ARBL302S

ARBL054

ARBL057

ARBL1010

ARBL052L

ARBL102L

ARBL202L

ARBL302L

ARBL104

ARBL107

ARBL2010

ARBL102G

ARBL202M

Y branch

Header

4 branch

7 branch

10 branch

Содержание MULTI V PLUS LRUC1008T1



















































































Результаты поиска

Содержание MULTI V PLUS LRUC1008T1

Отзывы:

Похожие инструкции для MULTI V PLUS LRUC1008T1

Бренды по названию

Популярные бренды

LG MULTI V PLUS LRUC1008T1, Руководство по установке

Результаты поиска

Содержание MULTI V PLUS LRUC1008T1

Отзывы:

Похожие инструкции для MULTI V PLUS LRUC1008T1

Бренды по названию

Популярные бренды