LG LG A1C-V5 Series Скачать руководство пользователя страница 19

Страница: 19 / 108

Electronics

AC Module System Installation Manual

Rev. 1.0

Mount AC module to the PV rack in the following order:

•

Place AC modules on the PV rack with a minimum gap of 6mm (0.236 inches) between each module. To prevent the

risk of slipping during installation, mount AC modules one by one.

•

Peel the adhesive label attached on the side of AC module frame and attach the identification label on LG AC module

Installation map. The map makes it easy for customers to identify the physical location of a particular AC module.

Each AC module has two MAC ID labels. One is placed under the product specification label. And the other is the

detachable MAC ID label.

•

The layout of the array will be utilized for building a monitoring system allowing a customer to check the amount of

energy harvested.

•

The AC modules can be mounted in landscape or portrait orientation, as illustrated below.

•

When the AC module is mounted on a PV rack rail, ensure that the rail is inside the range specified in Appendix 2 –

Module Installation & Load Guide. The range varies depending on mounting methods.

•

Appendix 2 guides you how to place PV rack rails and clamps in connection with AC modules.

60 cell

① : 200mm (7.9 in)
② : 300mm (11.8 in)

This mounting method uses frame bolt holes.

Please refer to

Appendix 2 –Module Installation & Load Guide

②

•

To prevent the risk of accidents, use proper PPE (Personal Protective Equipment) including

helmets and gloves at all times.

•

If installation location is high above ground, make sure to use Fall Protection System during

the installation.

Design Strength (Basic Load)

•

60Cell Modules: 75lb/ft2

•

Detail of mounting distance is below.

Содержание LG A1C-V5 Series












































































































Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды

LG LG A1C-V5 Series, Руководство по установке

Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды