LG LG A1C-V5 Series Скачать руководство пользователя страница 58

Страница: 58 / 108

Electronics

AC Module System Installation Manual

Rev. 1.0

Step 5. Verify the system configuration

After connecting to the EnerBox2 through Soft AP mode, check the dashboard for the following. You can

also connect to EnerBox2 through the site’s routers.

A. Confirm that internet connection is secured.

B. Compare ‘Installed Number’ of AC modules with ‘Detected, Communicating or Producing Power’

of AC modules. This number will be refreshed in 15 min.

C. In areas like California, Hawaii or Molokai where Factory-installed grid profile (IEEE1547) is not

applied, users can edit grid profile by going [AC module - Set Grid Profile]. It takes 15 min to

update changes.

D. Click ‘Start Scan’. If the number of AC modules indicated matches the number installed then go

to the next step. If the number indicated is more than installed, delete the MAC addresses that

are not present in the “Installation Map” (modules may show up from an adjacent property).

EnerBox2 is connected to internet.

EnerBox2 is not connected to internet.

The number is matched.

Go on to next steps.

The number is more than the input number.

Delete MAC addresses that you cannot find

from ‘Installation Map’.

Make sure that the circuit breakers for branches where all of the installed AC modules are attached are

turned on.

Power production data will be refreshed within 30 min.

Содержание LG A1C-V5 Series












































































































Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды

LG LG A1C-V5 Series, Руководство по установке

Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды