LG LG A1C-V5 Series Скачать руководство пользователя страница 9

Страница: 9 / 108

Electronics

AC Module System Installation Manual

Rev. 1.0

1-4 FCC Guidelines

For Microinverter & Communication Gateway (EnerBox2)

You are cautioned that changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B Digital Device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction, may cause harmful

interference to radio communication. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

For Communication Gateway (EnerBox2)

Indoor use only

FCC Caution: For indoor use only; outdoor use or in any other environments not covered in this manual

may violate the FCC regulation and void the user’s authority to use the product.

Specially, within the 5.15-5.25 GHz band, U-NII device is restricted to indoor operations to reduce any

potential for harmful interference to co-channel MSS operations.

FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 8.87 inches (20 cm) between

the radiator and your body. End users must follow the specific operating instructions for satisfying RF

exposure compliance. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

CAUTION: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices

because their signals could interfere with critical aircraft instruments.

Содержание LG A1C-V5 Series












































































































Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды

LG LG A1C-V5 Series, Руководство по установке

Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды