LG LG A1C-V5 Series Скачать руководство пользователя страница 37

Страница: 37 / 108

Electronics

AC Module System Installation Manual

Rev. 1.0

An example for the grounding method is described below.

Using alternative equipment grounding devices.

•

Determine the size of an external ground wire according to Article 690.45, NEC2014.

•

All bare metal parts should be grounded through the connection of the PV module frame.

•

Alternative Equipment Grounding Devices are classified on a table at

Appendix 3 - Alternative Equipment

Grounding Devices.

•

Those methods and devices are not tested by UL.

•

These alternative grounding devices indicated on the appendix have been evaluated and approved by LG, not by UL.

•

Please follow installation manual for the grounding devices provided by its manufacturer.

The NEC section 690.43 states that "Exposed non-current carrying metal parts of module frames,

equipment, and conductor enclosures shall be grounded in accordance with 250.134 or 250.136(A)

regardless of voltage."

The devices are intended for single use only. Functionality will not be guaranteed if reused.

Samples for grounding

•

These alternative grounding devices indicated on the appendix have been evaluated and approved by LG, not by UL.

•

Please refer to

Appendix 3 - Alternative Equipment Grounding Devices

for alternative equipment grounding devices.

Alternative Equipment Grounding Devices

AC Junction Box

grounding

wire

Содержание LG A1C-V5 Series












































































































Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды

LG LG A1C-V5 Series, Руководство по установке

Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

Похожие инструкции для LG A1C-V5 Series

Бренды по названию

Популярные бренды