LG Hydro Kit Скачать руководство пользователя страница 49

Страница: 49 / 77

Accessories Installation

Hydro Kit

Installation Manual

ENGLISH

If you require to operate control depending on external digital input(ON/OFF), connect cable to
indoor PCB(CN_EXT).

Follow below procedures step 1 ~ step 4.

Step 1.

Check if the power of the unit is turned off.

Step 2.

Disassemble front panels and distinguish control box(Indoor) of the unit

Step 3.

Connect the external controller to PCB(CN_EXT) completely.

Step 4.

Connect the cable and field installation part.

Determining the purpose of CN_EXT

Setting value: 0 ~ 5 step Indoor CN-EXT port setting

- 0: default

- 1: Simple operation on / off

- 2: Dry contact (simple contact)

- 3: Emergency stop only for indoor unit

- 4: Reattachment / absence

- 5: Emergency stop of all indoor units (It can be set only when indoor unit has emergency stop

function)

External Controller

Indoor PCB

CN_EXT

Indoor PCB

Adapter Cable

Indoor Unit

Supplied Part

0.5 m

Max 10 m

Relay Circuit

Power
supply
of relay

PCB

Field Installation Part

Installation example #2

• SW : Single pole switch

- Select a part with contacts for extremely low

amperage

- DC 5 V ~ 12 V is used at the contact point
- Switch load is approximately 0.5 ~ 1 mA

• Control cable

- Cable size : 22 to 26 AWG
- Don’t extend the cable more than 10 meters

• X : Relay(a point of contact, fixed DC 0.5 ~ 1 mA)
• SW : Distance ON/OFF switch
• Control cable(Indoor unit to Relay Circuit)

- Cable size : 22 to 26 AWG
- Don’t extend the cable more than 10 meters

Indoor Unit

PCB

Supplied Part

Field Installation Part

0.5 m

Max 10 m

Installation example #1

CN_EXT

Содержание Hydro Kit














































































Результаты поиска

Содержание Hydro Kit

Отзывы:

Похожие инструкции для Hydro Kit

Бренды по названию

Популярные бренды

LG Hydro Kit, Руководство по установке

Результаты поиска

Содержание Hydro Kit

Отзывы:

Похожие инструкции для Hydro Kit

Бренды по названию

Популярные бренды