LG Hydro Kit Скачать руководство пользователя страница 33

Страница: 33 / 77

Installation

Hydro Kit

Installation Manual

ENGLISH

4. When separating remote controller from setup board, as the picture below, after inserting

into the lower separating hole using screw driver and then, spinning clockwise, remote
controller is separated.

- There are two separating holes. Please individually separate one at a time.

- Please be careful not to damage the inside components when separating.

6. Please use extension cable if the distance between wired remote controller and indoor

unit is more than 10 m.
Extension cable(10 m) model name : PZCWRC1

5. Please connect indoor unit and remote controller using connection cable.

Optional extension cable
(purchased separately)

Please check if connector
is normally connected.

Male plug ends

Female plug ends

Hydro Kit

When installing the wired remote controller, do not bury it in the wall.
(It can cause damage in the temperature sensor.)
Do not install the cable to be 50 m or above. (It can cause communication error.)

• When installing the extension cable, check the connecting direction of the connector of the

remote controller side and the product side for correct installation.

• If you install the extension cable in the opposite direction, the connector will not be connected.

• Specification of extension cable: 2547 1007 22# 2 core 3 shield 5 or above.

CAUTION

all Side

Содержание Hydro Kit














































































Результаты поиска

Содержание Hydro Kit

Отзывы:

Похожие инструкции для Hydro Kit

Бренды по названию

Популярные бренды

LG Hydro Kit, Руководство по установке

Результаты поиска

Содержание Hydro Kit

Отзывы:

Похожие инструкции для Hydro Kit

Бренды по названию

Популярные бренды