LG Hydro Kit Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 77

background image

System Set-Up

70

Hydro Kit

• DHW time setting

Determine following time duration : operation time of DHW tank heating, stop time of DHW tank
heating, and delay time of DHW tank heater operating.
- Active time : This time duration defines how long time DHW tank heating can be continued.
- Stop time : This time duration defines how long time DHW tank heating can be stopped. It is also

regarded as time gap between DHW tank heating cycle.

Th On

Th Off

0

-0.5 ℃

1.5 ℃

1

-1 ℃

2 ℃

2

-2 ℃

3 ℃

3

-3 ℃

4 ℃

• TH on/off Variable, heating air

Setting Thermal on/off Air Temperature gap in heating mode

• TH on/off Variable, heating water

Setting Thermal on/off Water Temperature gap in heating mode

• TH on/off Variable, cooling air

Setting the step value to adjust air temperature gap in cooling mode

Th On

Th Off

0

0.5 ℃

-0.5 ℃

1

1 ℃

-1 ℃

2

2 ℃

-2 ℃

3

3 ℃

-3 ℃

Th On

Th Off

0

0.5 ℃

-0.5 ℃

1

1 ℃

-1 ℃

2

2 ℃

-2 ℃

3

3 ℃

-3 ℃

Th On

Th Off

0

-2 ℃

2 ℃

1

-3 ℃

3 ℃

2

-4 ℃

4 ℃

3

-1 ℃

1 ℃

• TH on/off Variable, cooling water

Setting the step value to adjust water temperature gap in cooling mode

«
...
68
69
70
71
72
...
»

Содержание Hydro Kit














































































Отзывы:

Нет отзывов

Похожие инструкции для Hydro Kit

Бренд: Sanden Страницы: 26

Бренд: Nectre Fireplaces Страницы: 17

Бренд: Lasko Страницы: 4

Бренд: iGenix Страницы: 6

Бренд: Saxon Страницы: 12

Бренд: Davey Страницы: 4

Бренд: EINHELL Страницы: 44

SUPER T T6A60S-4LE2X FT4 Series

Бренд: GORMAN-RUPP PUMPS Страницы: 48

Бренд: BN Thermic Страницы: 8

Бренд: DeLonghi Страницы: 4

Бренд: Beliani Страницы: 7

Бренд: F.F. Group Страницы: 28

Бренд: Protemp Страницы: 51

GAU-NFA-HH-150K

Бренд: Larson Electronics Страницы: 12

Бренд: Ultranatura Страницы: 24

NKVE MCE Series

Бренд: DAB Страницы: 72

FlexxPump 250 OLED

Бренд: DLS Страницы: 80

SiFire EN 100/200-205-45 E

Бренд: Wilo Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды