LG Hydro Kit Скачать руководство пользователя страница 21

Страница: 21 / 77

Installation

Hydro Kit

Installation Manual

ENGLISH

3) Water Tank(DHW) + Floor Heating Installation(Default)

- For DHW / Floor Heating operation , ‘Dip switch #2’ should be set correctly.

- For sensing air temperature at specific area, remote temperature sensor(PQRSTA0) or wired

remote controller could be choose, depending on the ‘Dip switch #3’ setting.
*please refer the “System Set-Up, Dip Switch Setting”

- Wi-Fi module(PWFMDD200/105 cm) connected to ‘CN-WF’ on Hydro kit PCB. To increase the

length between Wi-Fi modem and Hydro Kit, please purchase USB Extension Cable(PWYREW000,
10 m)

- In case of floor cooling, please make sure to set cooling cut off temperature for preventing

condensation on the floor

- For 3-way, 2-way valve control, please refer the “Accessories Installation”

- The Heating operation mode of the hot water tank is not a mode selection by the remote controller,

it changes the 3-way valve direction to Water Tank base on the water tank temperature.

- It is impossible to operate Hot water(DHW) during cooling mode.

Drainage

Water Supply

FCU

(Cooling → Close)

PQRSTA0

Wired Remote

Controller

Wi-fi Module

(PWFMDD200)

Water Supply

Field Supply

LG Supply

Shut-Off valve

Balancing valve with flow meter

Expansion tank

Automatic air separator

Service port(Drain valve)

Pressure safety relief valve

Magnetic filter(Recommended)

Pressure meter

Water Pump

Check valve

Strainer

DHW

(Sanitary Water) Tank

Flow switch (Included in product)

Water Tank temperature Sensor (12 m)

Mode

Condition

3-way valve direction

2-way valve

Cooling

FCU – ‘Not use’

Under Floor

Open

FCU – ‘Use’

Under Floor

Heating

Priority – ‘DHW’

DHW / Sanitary Water Tank

No control

Priority – ‘UFH’

Under Floor

No control

NOTICE

Содержание Hydro Kit














































































Результаты поиска

Содержание Hydro Kit

Отзывы:

Похожие инструкции для Hydro Kit

Бренды по названию

Популярные бренды

LG Hydro Kit, Руководство по установке

Результаты поиска

Содержание Hydro Kit

Отзывы:

Похожие инструкции для Hydro Kit

Бренды по названию

Популярные бренды