LG 55EW960H Скачать руководство пользователя страница 65

Страница: 65 / 89

206-4307

Remote Jack Pack Setup

RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item

093

RJP AVAILABLE

appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE

to 1). See Installer Menu detailed descriptions for further information.

093 RJP AVAILABLE 001

TV Connections

Caution: Make these connections ONLY after Master TV Setup and TV cloning procedures

are complete. Also, make sure to use the RJ-45 Control cable from the RJP cable bundle to

make the connection to the TV’s RJP port. Do NOT connect a standard Ethernet cable to the

RJP port, as this may damage the TV and network equipment.

Refer to the figure below, and connect the RJ-45 Control cable from the RJP cable bundle to the RJP

port

on the TV’s rear jack panel. Then, connect HDMI and Composite Video/Audio connectors, as applicable,

for the cable bundle.

Reference: Remote Jack Pack / TV Connections & Setup

Note:

RGB is not supported on these TV models. If an RGB source is connected to a legacy

RJP, you will see a brief message on-screen to indicate that this device is not supported.

USB IN 1

SPEAKER OUT

LINE OUT

RJP Use Only

MPI

ANTENNA/

CABLE IN

OPTICAL

DIGITAL

AUDIO OUT

RESET

UPDATE

SERVICE

RS-232C IN

(CONTROL)

LAN

AUX LAN

PTC SERVICE

(SERVICE ONLY)

AV IN

Audio In

HDMI IN 1

Connect HDMI connector

from RJP cable bundle.

AUDIO/VIDEO IN

Connect Composite Video/Audio

connectors from RJP cable bundle.

(Composite Video on legacy RJP only.)

RJP Use Only

Connect RJ-45 Control cable from RJP

cable bundle.

Note:

Before connecting the RJP

cable bundle, you may need to remove

the gray RJP cover that isintended to

prevent accidental misuse of the port.

Содержание 55EW960H


























































































Результаты поиска

Содержание 55EW960H

Отзывы:

Похожие инструкции для 55EW960H

Бренды по названию

Популярные бренды

LG 55EW960H, Руководство по настройке коммерческого режима

Результаты поиска

Содержание 55EW960H

Отзывы:

Похожие инструкции для 55EW960H

Бренды по названию

Популярные бренды