Lexmark X734DE Скачать руководство пользователя | Manualshive

Страница: 267 / 626

background image

Repair information

4-1

7526

Go Back

Previous

Next

4. Repair information

Safety information

•

The safety of this product is based on testing and approvals of the original design and specific
components. The manufacturer is not responsible for safety in the event of use of unauthorized
replacement parts.

•

The maintenance information for this product has been prepared for use by a professional service person
and is not intended to be used by others.

•

CAUTION:

When you see this symbol, there is a danger from hazardous voltage in the area of the

product where you are working. Unplug the product before you begin, or use caution if the product
must receive power in order to perform the task.

Removal and cleaning precautions

Observe the following precautions whenever you service the printer:

•

Be sure to unplug the printer from the outlet before attempting to service the printer.

•

To reassemble the printer, reverse the order of removal unless otherwise specified.

•

Do not operate the printer anytime during removals. If it is absolutely necessary to run the printer with its
covers removed, use care not to allow your clothing to be caught in revolving parts such as the gears,
rollers and fan motor.

•

Never touch the terminals of electrical parts or high-voltage parts such as the high-voltage power supply.

•

After part replacement, ensure the wiring harness is not caught or damaged.

•

Do not attempt to cut or extend the wiring harness.

•

Confirm the wiring harness connector is connected properly.

•

Be sure to handle the fuser carefully as it remains hot for a while after the printer stops running. Always
unplug connectors by holding the connector housing.

Warning:

Read the following before handling electronic parts.

CAUTION—POTENTIAL INJURY:

The printer weight is greater than 97 lbs (44kg), and requires three or more trained personnel to lift
safety.

«
...
265
266
267
268
269
...
»

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X734DE

Accel-a-Writer 8300

Бренд: Xante Страницы: 12

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 16

imageRUNNER ADVANCE C3330 Series

Бренд: Canon Страницы: 5

imagePROGRAF TA-30

Бренд: Canon Страницы: 49

Бренд: Canon Страницы: 210

Color imageCLASS MF8180c

Бренд: Canon Страницы: 34

Бренд: Xerox Страницы: 44

Бренд: Oki Страницы: 76

Бренд: Pantum Страницы: 115

Бренд: Savin Страницы: 160

TELEIOS GRANDE G5

Бренд: d.gen Страницы: 14

Бренд: Cashino Страницы: 74

PR-INT-MX-RAVAS-ABLE

Бренд: Ravas Страницы: 26

WorkCentre PRO 35

Бренд: Xerox Страницы: 13

Бренд: Glunz & Jensen Страницы: 104

Бренд: Microcom Страницы: 73

Бренд: SATO Страницы: 255

Accel-a-Writer 8200

Бренд: Xante Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды