Lexmark X734DE Скачать руководство пользователя

Страница: 20 / 626

Service Manual

7526

Go Back

Preface

This manual contains maintenance procedures for service personnel. It is divided into the following chapters:

General information

contains a general description of the MFP and the maintenance approach used to

repair it. Special tools and test equipment, as well as general environmental and safety instructions, are
discussed.

Diagnostic information

contains an error indicator table, symptom tables, and service checks used to

isolate failing field replaceable units (FRUs).

Diagnostic aids

contains tests and checks used to locate or repeat symptoms of MFP problems.

Repair information

provides instructions for making MFP adjustments and removing and installing FRUs.

Connector locations

uses illustrations to identify the connector locations and test points on the MFP.

Preventive maintenance

contains the lubrication specifications and recommendations to prevent

problems.

Parts catalog

contains illustrations and part numbers for individual FRUs.

Appendix A

contains service tips and information.

Appendix B

contains representative print samples.

Change history

Revision date

Updates

2013/06/25

Added CPU fan removals and parts catalog entry.

2012/11/15

Updated part numbers in Assembly 2:

“Front” on page 7-5

• 40X8110 replaced 40X5093
• 40X8111 replaced 40X5094
• 40X8112 replaced 40X5095

2012/06/13

Added the topic

“Print quality—white gapping” on page 2-157

2012/06/01

Added the topic

“Cartridge guide wheel removal” on page 4-63

2011/11/03

• Added the

“Auger drive removal” on page 4-56

• Added the

“Waste toner HV contact assembly removal” on page 4-213

• Added the

“Contact springs kit removal” on page 4-79

with the following sub

removals:

“Charge roll contact spring removal” on page 4-79
“HVPS contact springs removal” on page 4-80
“Torsion spring removal” on page 4-81

, which was formerly contact spring removal

• Updated the

“Left” on page 7-11

to add the auger drive and shaft and waste toner HV

contact part numbers.

• Updated the illustration for

“Left” on page 7-10

to include the auger drive and shaft and

waste toner HV contact.

2011/08/11

Changed the part number for the fax modem card from 40X4821 to 40X7055 for

“Options

and features” on page 7-25

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X734DE

Отзывы:

Похожие инструкции для X734DE

Бренды по названию

Популярные бренды

Lexmark X734DE, Руководство по обслуживанию

Результаты поиска

Содержание X734DE

Отзывы:

Похожие инструкции для X734DE

Бренды по названию

Популярные бренды