manualshive.com logo in svg

Lexmark X734DE, Руководство по обслуживанию

Поделиться
Скачать
Lexmark X734DE Скачать руководство пользователя страница 234

3-38

Service Manual

7526

  

Go Back

Previous

Next

Scanner Manual Registration

This item is used to manually register the flatbed and ADF on the MFP scanner unit. Registration should be 
performed whenever the ADF unit, flatbed unit, or controller card are replaced.

To manually adjust the scanner:

1.

Touch 

Scanner Manual Registration.

2.

Touch 

Print Quick Test

.

3.

Place the quick test on the glass of the flatbed scanner.

4.

Press 

Copy Quick Test

.

5.

Select 

Flatbed

.

Examine the copy of the Quick Test and compare it to the original. Adjust the Left Margin and/or the Top 
Margin to match the original.

6.

Touch 

Submit

.

Submitting changes…

 is displayed.

7.

Place the original printout on the glass of the flatbed, and touch 

Copy Quick Test

.

8.

If the pages match, continue to step 9. If the pages do not match, repeat steps 4 through 7, until you are 
satisfied.

9.

Place the original in the ADF, and touch Copy Quick Test.

10.

Examine the copy of the Quick Test and compare it to the original. If it does not match, continue. If it does 
match, go to step 11. If it matches go to step 16.

Selection

Effect

Left Margin

• Decrease the value and move the margin to the left.
• Increase the value and move the margin to the right

Top Margin

• Decrease the value to move the margin down
• Increase the value to move the margin upward.

Scanner Manual Registration

Copy Quick Test

Flatbed

ADF Front

ADF Back

Print Quick Test

Flatbed

Top Margin

Left Margin

-7

3

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды