Lexmark X734DE Скачать руководство пользователя | Manualshive

Страница: 2 / 626

background image

Edition: June 25, 2013

The following paragraph does not apply to any country where such provisions are inconsistent with local law

:

LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the
programs described may be made at any time.
Comments may be addressed to Lexmark International, Inc., Department D22X/022-1, 740 West New Circle Road,
Lexington, Kentucky 40550, U.S.A or e-mail at [email protected]. Lexmark may use or distribute any
of the information you supply in any way it believes appropriate without incurring any obligation to you.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these
available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or
imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that
does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in
conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the
user’s responsibility.
Lexmark, Lexmark with diamond design, and MarkNet are trademarks of Lexmark International, Inc., registered in the
United States and/or other countries.
PrintCryption is a trademark of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company.
All other trademarks are the property of their respective owners.

© 2009 Lexmark International, Inc.

All rights reserved.

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software
and documentation developed exclusively at private expense.

P/N 12G9821

7526

«
1
2
3
4
...
»

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X734DE

Бренд: J&Maya Страницы: 21

Document Centre 255 LP

Бренд: Xerox Страницы: 158

tecjet 6090DTG-dx5

Бренд: TEC Страницы: 73

Бренд: Tally Страницы: 106

C5020N - FS Color LED Printer

Бренд: Kyocera Страницы: 410

Бренд: Ricoh Страницы: 44

Бренд: Oki Страницы: 187

Бренд: SII Страницы: 85

Бренд: Ricoh Страницы: 162

Бренд: Pantum Страницы: 111

Бренд: Lexmark Страницы: 729

DocuCentre-VI C2264

Бренд: Fuji Xerox Страницы: 129

Бренд: Oki Страницы: 64

Бренд: Mita Страницы: 134

Бренд: SIGN RACER Страницы: 73

GG IMAGE P4100 Series

Бренд: G&G Страницы: 102

Бренд: Canon Страницы: 37

Бренд: Canon Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды