LevelOne Infinity IES-0880 Скачать руководство пользователя страница 133

Страница: 133 / 144

IES-0880 User Manual

Page 133

Usage:

Use

ip igmp snooping report-suppression

command to enable report suppression for

IGMP versions 1 and 2.
Use the

no ip igmp snooping report-suppression

command to disable report

suppression.

3.

Command Syntax:

(no) ip igmp snooping report-suppression

4.

Example:

The following example enables report suppression for IGMPv2 reports on

vlan1.1

switch_a(config)#interface vlan1.1
switch_a(config-if )#ip igmp version 2
switch_a(config-if )#ip igmp snooping report-suppression
switch_a(config-if )#

NTP

NTP Status:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

ntp enable

command to enable NTP for the Switch.

Use

no ntp enable

command to disable NTP for the Switch.

Command Syntax:

(no) ntp enable

4.

Example:

The following example enables NTP for the Switch:

switch_a(config)#ntp enable
switch_a(config)#

NTP Server:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Содержание Infinity IES-0880

















































































































































Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды

LevelOne Infinity IES-0880, Руководство пользователя

Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды