LevelOne Infinity IES-0880 Скачать руководство пользователя страница 115

Страница: 115 / 144

IES-0880 User Manual

Page 115

The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server trap-type enable coldStart

command to enable cold start trap for

SNMP.
Use the

no snmp-server trap-type enable coldStart

command to disable cold start trap

for SNMP.

3.

Command Syntax:

(no) snmp-server trap-type enable coldStart

4.

Example:

The following example enables cold start trap for SNMP:

switch_a(config)#snmp-server trap-type enable coldStart
switch_a(config)#

Warm Start Trap:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server trap-type enable warmStart

command to enable warm start trap for

SNMP.
Use the

no snmp-server trap-type enable warmStart

command to disable warm start

trap for SNMP.

3.

Command Syntax:

(no) snmp-server trap-type enable warmStart

4.

Example:

The following example enables warm start trap for SNMP:

switch_a(config)#snmp-server trap-type enable warmStart
switch_a(config)#

Link Down Trap:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Содержание Infinity IES-0880

















































































































































Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды

LevelOne Infinity IES-0880, Руководство пользователя

Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды