LevelOne Infinity IES-0880 Скачать руководство пользователя страница 85

Страница: 85 / 144

IES-0880 User Manual

Page 85

Example:

The following example shows setting

storm-control level

LEVEL (

) to the interface fe1

(port 1):

switch_a(config)#interface fe1
switch_a(config-if )#storm-control level 30
switch_a(config-if )#

Broadcast:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1
switch_a(config-if )#

Usage:

Use

storm-control broadcast enable

command to enable broadcast traffic.

Use

no storm-control broadcast

command to disable broadcast traffic.

Command Syntax:

storm-control broadcast enable
no storm-control broadcast

4.

Example:

The following example shows setting

storm-control broadcast enable

to the interface

fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if )#storm-control broadcast enable
switch_a(config-if )#

Multicast:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1
switch_a(config-if )#

Usage:

Use

storm-control multicast enable

command to enable multicast traffic.

Содержание Infinity IES-0880

















































































































































Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды

LevelOne Infinity IES-0880, Руководство пользователя

Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды