LevelOne Infinity IES-0880 Скачать руководство пользователя страница 116

Страница: 116 / 144

IES-0880 User Manual

Page 116

Usage:

Use

snmp-server trap-type enable linkDown

command to enable link down trap for

SNMP.
Use the

no snmp-server trap-type enable linkDown

command to disable link down trap

for SNMP.

3.

Command Syntax:

(no) snmp-server trap-type enable linkDown

4.

Example:

The following example enables link down trap for SNMP:

switch_a(config)#snmp-server trap-type enable linkDown
switch_a(config)#

Link Up Trap:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server trap-type enable linkUp

command to enable link up trap for SNMP.

Use the

no snmp-server trap-type enable linkUp

command to disable link up trap for

SNMP.

3.

Command Syntax:

(no) snmp-server trap-type enable linkUp

4.

Example:

The following example enables link up trap for SNMP:

switch_a(config)#snmp-server trap-type enable linkUp
switch_a(config)#

Authentication Failure Trap:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server trap-type enable authenticationFailure

command to enable

authentication failure trap for SNMP.
Use the

no snmp-server trap-type enable authenticationFailure

command to disable

Содержание Infinity IES-0880

















































































































































Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды

LevelOne Infinity IES-0880, Руководство пользователя

Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды