LevelOne Infinity IES-0880 Скачать руководство пользователя страница 123

Страница: 123 / 144

IES-0880 User Manual

Page 123

switch_a(config)#

Retransmit:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use this command to specify the number of times the Switch transmits each radius
request to the server before giving up.

3.

Command Syntax:

radius-server retransmit RETRIES
no radius-server retransmit

RETRIES <1-100> Specifies the retransmit value. Enter a value in the range 1 to 100.

Example:

The following example specifies the retransmit value

switch_a(config)#radius-server retransmit 12
switch_a(config)#

Port Authentication

Authentication State:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.
fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1
switch_a(config-if )#

Usage:

Use

dot1x reauthetication

command to enable reauthentication on a port.

Use

no dot1x reauthetication

command to disable reauthentication on a port.

Command Syntax:

(no) dot1x reauthentication

4.

Example:

The following example specifies to enable reauthetication on the interface fe1 (port 1):

switch_a(config)#interface fe1
switch_a(config-if )#dot1x reauthentication

Содержание Infinity IES-0880

















































































































































Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды

LevelOne Infinity IES-0880, Руководство пользователя

Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды