LevelOne Infinity IES-0880 Скачать руководство пользователя страница 76

Страница: 76 / 144

IES-0880 User Manual

Page 76

Logon to Privileged Exec Mode (Enable Mode).
The

switch_a#

prompt will show on the screen.

switch_a#

Usage:

Use

restore default

command to restore default setting of the switch.

Command Syntax:

restore default

4.

Example:

The following example restores default setting of the switch:

switch_a#restore default
switch_a#

Auto Save:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use this command to enable auto save configuration function. The configuration will be
automatically saved at every configured interval while this command is enabled. Use the
no form of this command to disable this feature.

3.

Command Syntax:

service auto-config enable
no service auto-config enable

4.

Example:

The following example enables or disables auto save configuration to switch:

switch_a(config)#service auto-config enable
switch_a(config)#no service auto-config enable
switch_a(config)#

Auto Save Interval (5~65536 sec):
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Содержание Infinity IES-0880

















































































































































Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды

LevelOne Infinity IES-0880, Руководство пользователя

Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды