LevelOne Infinity IES-0880 Скачать руководство пользователя страница 117

Страница: 117 / 144

IES-0880 User Manual

Page 117

authentication failure trap for SNMP.

3.

Command Syntax:

(no) snmp-server trap-type enable authenticationFailure

4.

Example:

The following example enables authentication failure trap for SNMP:

switch_a(config)#snmp-server trap-type enable authenticationFailure
switch_a(config)#

Topology Change Trap:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server trap-type enable topologyChange

command to enable topology

change trap for SNMP.
Use the

no snmp-server trap-type enable topologyChange

command to disable

topology change trap for SNMP.

3.

Command Syntax:

(no) snmp-server trap-type enable topologyChange

4.

Example:

The following example enables topology change trap for SNMP:

switch_a(config)#snmp-server trap-type enable topologyChange
switch_a(config)#

SNMP v1/v2c

Get Community Name:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server community get

command to specify and

no snmp-server community

get

command to remove get community name for SNMP.

Command Syntax:

snmp-server community get NAME

Содержание Infinity IES-0880

















































































































































Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды

LevelOne Infinity IES-0880, Руководство пользователя

Результаты поиска

Содержание Infinity IES-0880

Отзывы:

Похожие инструкции для Infinity IES-0880

Бренды по названию

Популярные бренды