Leuze 50116368 Скачать руководство пользователя

Страница: 63 / 116

Electrical connection

Leuze electronic GmbH + Co. KG

BCL 308

7.2

BCL 308

electrical connection

For the electrical connection of the BCL 308

, 2 connection variants are available.

The voltage supply (18 … 30 V DC) is connected acc. to the connection type selected.
2 freely programmable switching inputs/outputs for individual adaptation to the respective application are

also available here. Detailed information on this topic can be found in Chapter 7.3.1.

7.2.1 MS 308 connector hood with 3 integrated M12 connectors

The MS 308 hood with integrated connectors features three M12 connector plugs and a Mini-B type USB

socket as a service interface. Parameter memory is integrated into the MS 308 which temporarily stores

the settings of the BCL 308

in the case of replacement and transmits them to a new device.

Figure 7.2: BCL 308

- MS 308 connection hood with M12 connectors

7.2.2 ME 308 103 connection hood with M12 connection cables

The ME 308 103 connection hood features three connection cables with M12 connectors and a

Mini

B type USB socket as service interface. Parameter memory is integrated into the ME 308 103 which

temporarily stores the settings of the BCL 308

in the case of replacement and transmits them to a new

device.

NOTE

The shielding connection is done via the M12 connector housing.

NOTE

The integrated parameter memory for the simple replacement of the BCL 308

is located in the

MS 308. In the integrated parameter memory, both the settings and the network address are

saved and transmitted to a new device.

NOTE

In the case of Ethernet linear topology, the network is interrupted when the BCL 308

is removed

from the MS 308.

NOTE

Dimensioned drawing on see chapter 5.3.5 "Dimensioned drawings of MS 3xx / ME 3xx /

MK 3xx connection hoods" on Page 40.

PWR / SW IN/OUT

SWIO_2

SWIO_1

GNDIN

VIN

SERVICE

GND

D+

D-

BUS OUT

HOST / BUS IN

TD+ 1

RD+

RD-

TD-

TD+ 1

RD+

RD-

TD-

Mini-B USB socket

(behind protective cap)

M12 connector

(A-coded)

M12 socket

(D-coded)

Ethernet 0

M12 socket

(D-coded)

Ethernet 1

Connector hood

MS 308

Ethernet 1 LED

(split, two-colored):

ACT1 / LINK1

Ethernet 0 LED

(split, two-colored):

ACT0 / LINK0

Содержание 50116368





















































































































Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды

Leuze 50116368, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды