Leuze 50116368 Скачать руководство пользователя

Страница: 103 / 116

Online commands

Leuze electronic GmbH + Co. KG

BCL 308

101

Writing parameter set

Command

’PT’

Description

The parameters of the BCL 308

are grouped together in a parameter set and perma

nently stored in memory. There is one parameter set in permanent memory and one

operating parameter set in volatile memory; in addition, there is a default parameter set

(factory parameter set) for initialization. This command can be used to edit the first two

parameter sets (in permanent and volatile memory). A check sum can be used for reli

able parameter transfer.

Parameter

PT<BCC type><PS type><Status><Adr.><P.value adr.>

<P.value adr+1>…[;<Adr.><P.value adr.>][<BCC>]

<BCC type> Check-digit function during transfer,

unit [dimensionless]

’0’

No check digit

’3’

BCC mode 3

<PS type> Memory from which the values are to be read,

unit [dimensionless]

’0’

Parameter values stored in the flash memory

’3’

Operating values stored in RAM

<Status> Mode of parameter processing, without function here, unit [dimensionless]

’0’

No reset after parameter change, no further parameters

’1’

No reset after parameter change, additional parameters follow

’2’

With reset after parameter change, no further parameters

’6’

Set parameters to factory settings, no further parameters

’7’

Set parameters to factory settings, lock all code types; the code-type setting

must follow in the command!

<Adr.>

Relative address of the data within the data set,

’aaaa’

Four-digit, unit [dimensionless]

<P.value> Parameter value of the -bb- parameter stored at this address. The parameter

set data is converted from HEX format to a 2-byte-ASCII format for transfer.

<BCC> Check sum calculated as specified under BCC type

Acknowledg

ment

’PS=<aa>’

Parameter reply:

<aa>

Status acknowledgment, unit [dimensionless]

’01’

Syntax error

’02’

Impermissible command length

’03’

Impermissible value for checksum type

’04’

Invalid check sum received

’05’

Impermissible data length

’06’

Invalid data (parameter limits violated)

’07’

Invalid start address

’08’

Invalid parameter set

’09’

Invalid parameter set type

Содержание 50116368





















































































































Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды

Leuze 50116368, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды