Leuze 50116368 Скачать руководство пользователя

Страница: 67 / 116

Electrical connection

Leuze electronic GmbH + Co. KG

BCL 308

Figure 7.6: BCL 308

- MK 308 terminal hood with spring-cage terminals

Cable fabrication and shielding connection
Remove approx. 78 mm of the connection cable sheathing. 15 mm of sheath of the shielded line must be

freely accessible.

Figure 7.7: Cable fabrication for MK 308 terminal hood
The shield is automatically contacted when the cable is lead into the metal screw fitting and fastened when

the cord grip is closed. Then lead the individual wires into the terminals according to the diagram. Wire end

sleeves are not necessary.

NOTE

The integrated parameter memory for the simple replacement of the BCL 308

is located in the

MK 308. In the integrated parameter memory, both the settings and the network address are

saved and transmitted to a new device.

NOTE

In the case of Ethernet linear topology, the network is interrupted when the BCL 308

is removed

from the MK 308.

NOTE

Dimensioned drawing on see chapter 5.4 "Reading field curves / optical data" on Page 41.

Terminal hood

MK 308

SERVICE

GND

D+

D-

Mini-B USB socket

(behind protective cap)

rmi

nal bl

ock

R /

IN/O

rmi

nal bl

ock

HOST

BUS IN

(Ethernet 0

)

Terminal designation

MK 308

rmi

nal bl

ock

BUS OUT

(Ethernet 1

)

Ethernet 1 LED

(split, two-colored):

ACT1 / LINK1

Ethernet 0 LED

(split, two-colored):

ACT0 / LINK0

LEDs

MK 308

≈ 55 mm

≈ 8 mm

≈ 15 mm

Содержание 50116368





















































































































Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды

Leuze 50116368, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды