Leuze 50116368 Скачать руководство пользователя

Страница: 66 / 116

Electrical connection

Leuze electronic GmbH + Co. KG

BCL 308

Figure 7.5: BCL 308

- ME 338 214 connection hood with M8/M12/RJ45 connection cables

7.2.5 MK 308 terminal hood with spring-cage terminals

The MK 308 terminal hood makes it possible to connect the BCL 308

directly and without additional

connectors. The MK 308 features three cable lead-throughs in which the shielding connection for the inter

face cable is also located. The BCL 308

is also to be configured when the MK 308 is in a closed state via

a Mini-B type USB socket functioning as the service interface. Parameter memory is integrated into the

MK 308 which temporarily stores the settings of the BCL 308

in the case of replacement and transmits

them to a new device.

NOTE

The shielding connection is done via the M12 connector housing.

NOTE

The integrated parameter memory for the simple replacement of the BCL 308

is located in the

ME 308 214. In the integrated parameter memory, both the settings and the network address are

saved and transmitted to a new device.

NOTE

In the case of Ethernet line topology, the network is interrupted when the BCL 308

is removed

from the ME 308 214.

NOTE

Dimensioned drawing on see chapter 5.3.5 "Dimensioned drawings of MS 3xx / ME 3xx /

MK 3xx connection hoods" on Page 40.

Connection hood

ME 308 214

①
②

③
④

⑤

PWR

SWIO_2

n. c.

GNDIN

VIN

HOST / BUS IN

BUS OUT

SERVICE

3 4 5

GND

SENSOR

SWIO_1

n. c.

GNDOUT

VOUT

TD+

RD+

TD+

RD+

Mini-B USB socket

(behind protective cap)

M12 connector

(A-coded)

Ethernet 0

RJ45 socket

Ethernet 1

RJ45 socket

M8 socket

(ext. sensor)

Ethernet 1

LED (split, two-colored):

ACT1 / LINK1

Ethernet 0

LED (split, two-colored):

ACT0 / LINK0

①

②

③

④

⑤

Содержание 50116368





















































































































Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды

Leuze 50116368, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды