Leuze 50116368 Скачать руководство пользователя

Страница: 102 / 116

Online commands

Leuze electronic GmbH + Co. KG

BCL 308

100

Command

’PD’

Description

This command outputs the difference between the default parameter set and the operat

ing parameter set or the difference between the default parameter set and the perma

nent parameter set.

Comment:

The reply supplied by this command can e.g. be directly used for programming a device

with factory settings, whereby this device receives the same configuration as the device

on which the PD-sequence was executed.

Parameter

’PD<P.set1><P.set2>’

<P.set1> Parameter data set which is to be copied,

unit [dimensionless]

’0’

Parameter data set in permanent memory

’2’

Default or factory parameter set

<P.set2> Parameter set to which the data is to be copied, unit [dimensionless]

’0’

Parameter data set in permanent memory

’3’

Operating parameter data set in volatile memory

Permissible combinations here include:

’20’

Output of the parameter differences between the default and the permanently

saved parameter set

’23’

Output of the parameter differences between the default parameter set and

the operating parameter set saved in volatile memory

’03’

Output of the parameter differences between the permanent parameter set

and the operating parameter set saved in volatile memory

Acknowledg

ment

positive

PT<BCC><PS type><Status><Adr.><P.value adr.><P.va1>…

[;<Adr.><P.value adr.>]

<BCC>

’0’

No check digit

’3’

BCC mode 3

’0’

Values stored in flash memory

’3’

Operating values stored in RAM

’0’

No further parameters

’1’

Additional parameters follow

<Adr.>

Relative address of the data within the data set

’aaaa’

Four-digit, unit [dimensionless]

<P.value>Parameter value of the -bb- parameter stored at this address. The parameter

set data is converted from HEX format to a 2-byte-ASCII format for transfer.

Acknowledg

ment

negative

’PS=<aa>’

<aa>

Status acknowledgment, unit [dimensionless]

’0’

No difference

’1’

Syntax error

’2’

Impermissible command length

’6’

Impermissible combination, parameter set 1 and parameter set 2

’8’

Invalid parameter set

Содержание 50116368





















































































































Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды

Leuze 50116368, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды