Lenovo ThinkCentre M800 Скачать руководство пользователя

Страница: 147 / 178

11. Position the heat sink fan duct on the top of the new heat sink and fan assembly as shown. Then, press

the heat sink fan duct straight down until it snaps into position.

Figure 100. Installing the heat sink fan duct

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.

Replacing the microprocessor

CAUTION:

The heat sink and microprocessor might be very hot. Before you open the computer cover, turn off
the computer and wait several minutes until the computer is cool.

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the microprocessor, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 88.

3. Lay the computer on its side for easier access to the system board.

4. Locate the microprocessor. See “Computer components” on page 31.

5. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 137.

Note:

Place the heat sink and fan assembly on its side so that the thermal grease on the bottom of it

does not get in contact with anything.

Chapter 9

Installing or replacing hardware

139

Содержание ThinkCentre M800


















































































































































































Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Похожие инструкции для ThinkCentre M800

Бренды по названию

Популярные бренды

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Похожие инструкции для ThinkCentre M800

Бренды по названию

Популярные бренды