manualshive.com logo in svg

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части, Страница: 96 / 178

Поделиться
Скачать
Lenovo ThinkCentre M800 Скачать руководство пользователя страница 96

Use the instructions shipped with the option to help you make the connection and install any software
or device drivers that are required for the option.

Removing the computer cover

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

CAUTION:

Before you open the computer cover, turn off the computer and wait several minutes until the
computer is cool.

To remove the computer cover, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Unlock any locking device that secures the computer cover.

3. Hold the sides of your computer and gently lay it down so that the computer cover is facing up.

4. Remove the two screws that secure the computer cover. Then, slide the cover to the rear of the

computer to remove it.

Figure 9. Removing the computer cover

Replacing the front bezel

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the front bezel, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 88.

88

ThinkCentre M800 and M900 Hardware Maintenance Manual

Содержание ThinkCentre M800



















































































































































































Отзывы:

Нет отзывов