manualshive.com logo in svg

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части

Lenovo ThinkCentre M800 - Это надежный настольный компьютер для бизнеса с высокой производительностью. Не забудьте скачать бесплатное руководство по обслуживанию аппаратных средств из manualshive.com, чтобы узнать, как получить максимальную отдачу от вашего устройства.

Поделиться
Скачать
background image

• If your computer has a secondary power switch on the rear of the computer, ensure that it is switched on.

• The power indicator on the front of the computer is on.

• The computer voltage matches the voltage available at the electrical outlet for your country or region.

The operating system fails to start up

Solution: Ensure that the startup sequence includes the device where the operating system resides. Usually,
the operating system is on the storage drive. For more information, see “Changing the startup device
sequence permanently” on page 65.

The computer beeps multiple times before the operating system starts up

Solution: Ensure that no keys are stuck.

Audio problems

This section provides solutions to audio-related problems.

No audio in Windows

Solutions:

• If you are using powered external speakers that have an On/Off control, ensure that:

– The On/Off control is set to the

On

position.

– The speaker power cable is connected to a properly grounded, functional ac electrical outlet.

• If your external speakers have a volume control, ensure that the volume is not set too low.

• Click the volume icon in the Windows notification area on the taskbar. Ensure that the mute speakers

settings are not selected and none of the volume settings is set too low.

Note:

If the volume icon is not displayed in the Windows notification area, add the icon to the notification

area. See “Adding an icon to the Windows notification area” on page 43.

• Some models have a front audio panel you can use to adjust volume. If you have a front audio panel,

ensure that the volume is not set too low.

• Ensure that your external speakers (and headphones, if used) are connected to the correct audio

connector on the computer. Most speaker cables are color-coded to match the connector.

Note:

When external-speaker or headphone cables are connected to the audio connector, the internal

speaker, if present, is disabled. In most cases, if an audio adapter is installed in one of the expansion
slots, the audio function built into the system board is disabled. Therefore, you must use the audio
connectors on the audio adapter.

• Ensure that the program you are running is designed for use in the Microsoft Windows operating system.

If the program is designed to run in DOS, the program does not use the Windows sound feature. The
program must be configured to use SoundBlaster Pro or SoundBlaster emulation.

• Ensure that the audio device drivers are correctly installed.

Sound comes only from one external speaker

Solutions:

• Ensure that the speaker cable is inserted completely into the connector on the computer.

• Ensure that the cable that connects the left speaker to the right speaker is securely connected.

• Click the volume icon in the Windows notification area on the taskbar. Then, click the speaker icon on top

of the volume control. Click the

Levels

tab and ensure that the Balance settings are set correctly .

70

ThinkCentre M800 and M900 Hardware Maintenance Manual

Содержание ThinkCentre M800



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkCentre M800

Canon PIXMA MX882 Series Network Setup Manual preview
PIXMA MX882 Series
Бренд: Canon Страницы: 34
Canon MX470 Getting Started preview
MX470
Бренд: Canon Страницы: 4
Canon MX470 User Manual preview
MX470
Бренд: Canon Страницы: 913
Canon Laser Class 700 Series Setup Manual preview
Laser Class 700 Series
Бренд: Canon Страницы: 30
Canon Laser Class 700 Series Datasheet preview
Laser Class 700 Series
Бренд: Canon Страницы: 6
Canon Laser Class 700 Series Specification preview
Laser Class 700 Series
Бренд: Canon Страницы: 6
Canon Laser Class 700 Series Network Manual preview
Laser Class 700 Series
Бренд: Canon Страницы: 108
Canon PIXMA MX860 series Network Manual preview
PIXMA MX860 series
Бренд: Canon Страницы: 9
Canon imagePROGRAF iPF9400 Brochure & Specs preview
imagePROGRAF iPF9400
Бренд: Canon Страницы: 8
Canon PIXMA MX860 series Getting Started Manual preview
PIXMA MX860 series
Бренд: Canon Страницы: 93
Canon MP980 series Manual preview
MP980 series
Бренд: Canon Страницы: 20
Canon PIXMA MX922 Setup Manual preview
PIXMA MX922
Бренд: Canon Страницы: 30
Canon PIXMA MX922 Easy Setup preview
PIXMA MX922
Бренд: Canon Страницы: 2
Xerox 770 Safety Manual preview
770
Бренд: Xerox Страницы: 24
Samsung ML-6050 Manual Del Usuario preview
ML-6050
Бренд: Samsung Страницы: 82
Samsung ML-2525 Datasheet preview
ML-2525
Бренд: Samsung Страницы: 2
EBS HandJet 250 Operating Instructions Manual preview
HandJet 250
Бренд: EBS Страницы: 34
XYZ Printing da Vinci 2.0 Duo Product Manual preview
da Vinci 2.0 Duo
Бренд: XYZ Printing Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды