manualshive.com logo in svg

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части, Страница: 92 / 178

Поделиться
Скачать
Lenovo ThinkCentre M800 Скачать руководство пользователя страница 92

If the POST detects a problem, an error message appears on the screen. A single problem can cause several
error messages to appear. When you correct the cause of the first error message, the other error messages
probably will not be displayed next time you turn on the system.

Error code

POST error message

Description/Action

0135

Fan failure

The system might be overheating.

Press F10 to exit.

Note:

If the problem is caused by the

microprocessor fan, press F10 will
not solve the problem.

0211

Keyboard not found

When there is no keyboard detected,
the error message will be displayed.

0164

Memory size decreased

Press F10 to exit.

1762

Configuration change has occurred

This error message is displayed when
a hard disk drive or optical drive
change has been made.

Press F10 to exit.

1820

More than one external fingerprint
reader are attached. Power off and
remove all but the reader that you set
up within your main operating system.

If more than one external fingerprint
reader are connected to a computer,
this error message will be displayed.

Remove all of the fingerprint
keyboards except the one compatible
with the fingerprint application on
your computer.

1962

No operating system found. Press
any key to repeat boot sequence.

This error occurs only after the POST
is completed.

Press any key to repeat boot
sequence.

Miscellaneous error conditions

Message/Symptom

FRU/Action

Changing display colors

Display/Monitor

Computer will

not

power-off. See “Hard disk drive boot

error” on page 82.

1. Power Switch

2. System Board

3. Riser card, if installed.

Computer will

not

RPL from server

1. Ensure that network is in startup sequence as first

device or first device after diskette.

2. Ensure that network adapter is enabled for RPL.

3. Network adapter (Advise network administrator of

new MAC address)

84

ThinkCentre M800 and M900 Hardware Maintenance Manual

Содержание ThinkCentre M800



















































































































































































Отзывы:

Нет отзывов