manualshive.com logo in svg

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части, Страница: 148 / 178

Поделиться
Скачать
Lenovo ThinkCentre M800 Скачать руководство пользователя страница 148

6. Lift the small handle

1

and open the retainer

2

to access the microprocessor

3

.

Figure 101. Accessing the microprocessor

7. Lift the microprocessor straight up and out of the microprocessor socket.

Figure 102. Removing the microprocessor

Notes:

• Your microprocessor and socket might look different from the one illustrated.

• Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom.

• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be

kept as clean as possible.

8. Ensure that the small handle is in the raised position and the microprocessor retainer is fully open.

9. Remove the protective cover that protects the gold contacts of the new microprocessor.

10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align

the notches

1

on it with the tabs

2

in the microprocessor socket. Then, carefully lower the new

microprocessor straight down into the microprocessor socket.

140

ThinkCentre M800 and M900 Hardware Maintenance Manual

Содержание ThinkCentre M800



















































































































































































Отзывы:

Нет отзывов