Lenovo ThinkCentre M800 Скачать руководство пользователя страница 107

Страница: 107 / 178

Figure 29. Pivoting the drive bay assembly downward

14. Install the optical drive. See “Replacing the optical drive” on page 104.

15. Install the front bezel. See “Replacing the front bezel” on page 88.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 147.

Replacing the internal speaker

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the internal speaker, do the following:

1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect

all power cords from electrical outlets and disconnect all cables that are connected to the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 88.

3. Remove the front bezel. See “Replacing the front bezel” on page 88.

4. Remove the optical drive. See “Replacing the optical drive” on page 104.

5. Locate the internal speaker. See “Computer components” on page 31.

6. Press the retaining clip

in the direction as shown and pivot the drive bay assembly upward at the

same time.

Chapter 9

Installing or replacing hardware

Содержание ThinkCentre M800


















































































































































































Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части, Страница: 107 / 178

Результаты поиска

Содержание ThinkCentre M800

Отзывы: