Lenovo ThinkCentre M800 Скачать руководство пользователя страница 145

Страница: 145 / 178

10. Reinstall the computer cover and connect the cables. See “Completing the parts replacement” on

page 147.

11. Turn on the computer and all connected devices.

Note:

When the computer is turned on for the first time after replacing the coin-cell battery, an error

message might be displayed. This is normal after replacing the coin-cell battery.

12. Use the Setup Utility program to set the date, time, and any passwords. See “Using the Setup Utility

program” on page 61.

Replacing the heat sink and fan assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

CAUTION:

The heat sink and fan assembly might be very hot. Before you open the computer cover, turn off the
computer and wait several minutes until the computer is cool.

To replace the heat sink and fan assembly, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 88.

3. Locate the heat sink and fan assembly. See “Computer components” on page 31.

4. Pivot the two plastic retaining clips that secure the heat sink fan duct outward. Then, remove the heat

sink fan duct from the failing heat sink and fan assembly.

Figure 98. Removing the heat sink fan duct

5. Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system

board.

Chapter 9

Installing or replacing hardware

137

Содержание ThinkCentre M800


















































































































































































Результаты поиска

Содержание ThinkCentre M800

Отзывы:

Lenovo ThinkCentre M800, Руководство по техническому обслуживанию аппаратной части, Страница: 145 / 178

Результаты поиска

Содержание ThinkCentre M800

Отзывы: