Lenovo 7X16 Скачать руководство пользователя страница 28

Страница: 28 / 212

SNMP Trap ID: 21
CIM Prefix: IMM CIM ID: 0039

User Action:

Complete the following steps until the problem is solved:

1. Reconfigure the watchdog timer to a higher value.

2. Make sure that the BMC Ethernet-over-USB interface is enabled.

3. Reinstall the RNDIS or cdc_ether device driver for the operating system.

4. Disable the watchdog timer.

5. Check the integrity of the installed operating system.

6. If problem persists, collect Service Data log.

7. Contact Lenovo Support.

•

FQXSPBR4004I: Server timeouts set by user [arg1]: EnableOSWatchdog=[arg2],

OSWatchdogTimout=[arg3], EnableLoaderWatchdog=[arg4], LoaderTimeout=[arg5].

A user configures Server Timeouts

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0095

User Action:

Information only; no action is required.

•

FQXSPBR4005I: Management Controller [arg1]: Configuration saved to a file by user [arg2].

A user saves a Management Controller configuration to a file.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0109

User Action:

Information only; no action is required.

•

FQXSPBR4006I: Management Controller [arg1]: Configuration restoration from a file by user [arg2]

completed.

This message is for the use case where a user restores a Management Controller configuration from a file
and it completes.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0136

User Action:

ThinkSystem SN550 V2 Messages and Codes Reference

Содержание 7X16





















































































































































































































Результаты поиска

Содержание 7X16

Отзывы:

Lenovo 7X16, Справочник, Страница: 28 / 212

Результаты поиска

Содержание 7X16

Отзывы: