Lenovo 7X16 Скачать руководство пользователя страница 191

Страница: 191 / 212

3. If the problem persists, contact technical support.

•

FQXPMER0006I: UEFI factory default settings loaded successfully

Severity: Info

User Action:

Information only; no action is required.

•

FQXPMER0006M: Failed to load XCC factory default settings

Severity: Error

User Action:

1. Restart BMC via supported method and reboot the system.

2. Retry this operation again.

3. If the problem persists, perform AC power cycle. (wait several seconds between AC power is off and

on)

4. Retry this operation again.

5. If the problem persists, contact technical support.

•

FQXPMER0007I: BMC factory default settings loaded successfully

Severity: Info

User Action:

Information only; no action is required.

•

FQXPMNM0001G: Failed to set new BMC network parameters.

Severity: Warning

User Action:

1. Ensure input parameters are valid.

2. Wait for one minute and retry the setting.

3. Restart BMC via supported method and reboot the system.

4. Retry the setting change.

5. Use UEFI setup to change parameters (optional).

•

FQXPMNM0002I: Set BMC network parameters to new values.

Severity: Info

User Action:

Information only; no action is required.

•

FQXPMOS0001K: Bootx64.efi is not found. Failed to Boot OS.

Severity: Warning

User Action:

1. Restart BMC via supported method and reboot the system.

2. Reflash BMC firmware.

3. Reboot system and retry OS booting.

4. Perform AC reset or virtual reseat.

Chapter 4

XClarity Provisioning Manager events

187

Содержание 7X16





















































































































































































































Результаты поиска

Содержание 7X16

Отзывы:

Lenovo 7X16, Справочник, Страница: 191 / 212

Результаты поиска

Содержание 7X16

Отзывы: