LEGRAND D45 SYSTEM, Руководство по установке, Страница: 193 / 254

189
322050 Colour 7” handsfree indoor handset
Two different device configuration ways available:
WAY 1) Configuration settings by device keyboard
WAY 2)
Configuration settings by inserting phisical configurators
Configuration settings by device keyboard - WAY 1 :
INSTAllATION SETTINgS OPErATION lIST TABlE
SETUP OPErATION CODE AND
lIghT STATUS
NExT
OPErATION
MEANINg AND INFOrMATION FOr ThE OPErATION rEMArk
Set room number for
handset 11#
8 alarm lights and message light off “FFII#” correct parameter input: 1 long tone
Default room number: 101
wrong parameter input: 3 short tones
* return to main menu of installation setup, 1 short tone
other unsuccessful operation: 3 short tone
Set maximum
apartments quantity
per floor in a riser 12#
8 alarm lights and message light off “II#” or “I#” correct parameter input: 1 long tone Range:1-99
Default:4; it can be set only when
there is no setting for hardware
wrong parameter input: 3 short tones
* return to main menu of installation setup, 1 short tone
other unsuccessful operation: 3 short tones
Set external SOS to be
always on or always off 15#
message light will indicate status of
this setting item 1 SOS external switch or pushbutton always
open (NO): message light on, 1 long tone Default: always
open
0 SOS external switch or pushbutton always close (NC): message light off, 1 long tone
* return to main menu of installation setup, 1 short tone
other unsuccessful operation: 3 short tones
Enable and disable
function of monitoring
Small EP 17#
message light will indicate status of
this setting item 1 enable: handset can monitor Small EP: message light on, 1 long tone Default: cannot monitor Small EP. This
function is available only when the
function is set as Small EP function.
0 Shielded: handset can not monitor Small EP: message light off, 1 long tone
* return to main menu of installation setting, 1 short tone
other unsuccessful operation: 3 short tones
Return all the
parameters to default
value 19#
message light will indicate status of
this setting item 1 Get all the default parameters: message light on, 1 long tone
0 Do not get all the default parameters: message light off, 1 long tone
* return to main menu of installation setup, 1 short tone
other unsuccessful operation: 3 short tones
Enable and disable
sensors 21#
Message light is off. 8 alarm lights
will indicate status of each alarm
zone 1# 1 1 alarm zone with sensor: LED 1 on, a long tone. Default: (all) without sensor
0 1 alarm zone without sensor: LED 1 off, a long tone.
* return to previous menu, 1 short tone
other Ineffective operation: 3 short tones
… …
8# 1 8 alarm zone with sensor: LED 8 on, a long tone.
0 8 alarm zone without sensor: LED 8 off, a long tone.
* return to previous menu, 1 short tone
other unsuccessful operation: 3 short tones
* return to main menu of installation setting, 1 short tone
other unsuccessful operation: 3 short tones
Set NO and NC type of
sensors
22#
8 alarm lights will indicate status of
each alarm zone.
1# 1 always open (NO) sensor for alarm area 1: LED 1 on, 1 long tone Default: sensors for 8 alarm zones are
always open (NO).
0 always close (NC) sensor for alarm area 1: LED 1 off, 1 long tone
* return to previous menu, 1 short tone
other unsuccessful operation: 3 short tones
… …
8# 1 always open (NO) sensor for alarm area 8: LED 8 on, 1 long tone
0 always close (NC) sensor for alarm area 8: LED 8 off, 1 long tone
* return to previous menu, 1 short tone
other unsuccessful operation: 3 short tones
* return to main menu of installation setup, 1 short tone
other unsuccessful operation: 3 short tones
BT00472-b-en 03/06/2013