Lectrosonics HH Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 27

background image

defined at foot of this document, see below

common).

Power Up sequence and current draw

Prerequisite(s): FPGA IC programmed

Hold power button on test panel key pad for 3 seconds.

Observe behavior of test key pad LED

-10 LED turns on red, then -20 LED
turns on red then both off.

both LED's flash red once then
green once

Observe behavior of test key pad LCD

"000000"
"HH"
"Vx.xx"
"Hybrid"
?
?
?
?
frequency "Main" screen

a flashing antenna icon inside a

׎

indicates the PLL is not locked

Measure current draw

50 to 500 mA

(170)

Note

The goal here is only to ensure the audio board powers up and is not burning up with fever

20.20

Control Panel switch test

Prerequisite(s): FPGA IC programmed

Apply +3.0VDC, 500mA current limit in at battery contact J8 (J9 is circuit common)
LCD display and push button key pad installed

Observe LCD display and
verify the frequency "Main"

«
...
7
8
9
10
11
...
»

Содержание HH




























Отзывы:

Нет отзывов

Похожие инструкции для HH

Бренд: Tokai Страницы: 20

Бренд: Sandstrom Страницы: 32

Бренд: DAPAudio Страницы: 12

Бренд: Microtech Gefell Страницы: 18

Axino Synergy Core

Бренд: Antelope Страницы: 55

Бренд: Steren Страницы: 12

GPSMAP 8400 series

Бренд: Garmin Страницы: 82

Бренд: Pyle Страницы: 12

Бренд: Panasonic Страницы: 22

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 33

Бренд: Panasonic Страницы: 15

Бренд: Looperlative Страницы: 29

Бренд: RCA Страницы: 20

Бренд: RCA Страницы: 22

Бренд: Sharp Страницы: 40

CMT-HPR99XM Marketing

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды