Lectrosonics HH Скачать руководство пользователя страница 20

Страница: 20 / 27

level=0 (changes audio level to 0)

Measure audio signal level at demodulated carrier at radio board J3

-43.5 to -41.5dB(r)

(-42.5)

Mute unit by pressing S1

mute=2

mute audio 1=unmuted 2=muted

Measure audio signal level at demodulated carrier at radio board J3

≤

-45dB(r)

(-47)

Un-mute unit by pressing S1
Measure audio signal level at demodulated carrier at radio board J3

-43.5 to -41.5dB(r)

(-42.5)

Modulation distortion measurement

Prerequisite(s) Unit in set-up mode

DUT in "Passthru"

FREQ set to highest frequency

Audio Gain set to "Gain 0"
Gainsw set to "auto"

Note

Entering Set-up mode is not necessary if the Alternate Method is exercised.

-10 dBu, 250Hz, low distortion, sinusoidal signal in at audio input rig

Verify neither audio board LED (D5 nor D6) are red (limiter not activated)

Measure audio signal
distortion of the demodulated
carrier radio board RF J3 at
carrier frequency:

Highest freq

≤

0.55% THD+N

(0.35)

FREQ set to lowest frequency
measure audio signal
distortion.

Lowest freq

≤

0.55% THD+N

(0.35)

channel=xx,

set channel (0(00) to 1020 (ff)
in normal tuning mode, 80 is 512

≤

0.55% THD+N (0.35)

FREQ set to mid frequency
measure audio signal
distortion.

Middle freq

≤

0.55% THD+N

(0.35)

Содержание HH




























Результаты поиска

Содержание HH

Отзывы:

Похожие инструкции для HH

Бренды по названию

Популярные бренды

Lectrosonics HH, Процедура выравнивания

Результаты поиска

Содержание HH

Отзывы:

Похожие инструкции для HH

Бренды по названию

Популярные бренды