Lectrosonics HH Скачать руководство пользователя страница 25

Страница: 25 / 27

Note

Entering Set-up mode is not necessary if the Alternate Method is exercised.

DUT in "Passthru"

Frequency set to middle

Frequency set to middle frequency
Gainsw set to auto

gainsw=0

No audio signal at DUT input

Apply +2.0VDC, 500mA current limit in at battery contact J8 (J9 is circuit common)

Observe Battery Icon on LCD display

battery icon blinking ON/OFF

Using the test panel key pad navigate to the "BatMon" screen

bscale? (query battery telemetry scale setting, 26 to 80)

Press MENU/SEL button on the test panel key pad to shift from High to low Frequency on LCD screen

batcal=1 Forces battery telemetry low, note frequency.

batcal=3 Forces battery telemetry high, check for frequency shift of 3.5KHZ

Press UP or DWN button on the test panel key pad to adjust for 3.5 KHz freq.
shift

3.5 KHz +/- 0.1

(3.5)

bscale=xx (set battery telemetry scale setting, 26 to
80) to adjust for 3.5KHz frequency shift

3.5 KHz +/- 0.1 (3.5)

Repeat steps 40.180.40 to step 40.180.50 until no further adjustment is necessary to achieve 3.5 KHz freq. shift
Using the test panel key pad navigate to the frequency "Main" screen

batcal=0 (sets battery telemetry to normal)

Apply +2.25VDC, 500mA current limit in at battery contact J8 (J9 is circuit common)

Press Power button on the test panel key pad and hold for 3 to 4 second and watch LCD as unit powers down.
Measure current draw

0 to 4mA

(0)

Press Power buttons and hold for 3 seconds as unit powers on ON.
Measure current draw

300 to 350 mA

(275)
(?)

Содержание HH




























Результаты поиска

Содержание HH

Отзывы:

Похожие инструкции для HH

Бренды по названию

Популярные бренды

Lectrosonics HH, Процедура выравнивания

Результаты поиска

Содержание HH

Отзывы:

Похожие инструкции для HH

Бренды по названию

Популярные бренды