Lectrosonics HH Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 27

background image

2.8 to 3.4 KHz

(3.1)

1.5 to 1.9 KHz

(1.9)

Note

Pilot Tone signal frequency at demodulated carrier at radio board J3

31.999 to 32.001 KHz (32)

Noise measurements (low gain branch)

Prerequisite(s) Unit in set-up mode

Gain set to "0"

Note

Entering Set-up mode is not necessary if the Alternate Method is exercised.

Using the test panel key pad navigate to the "Compat" screen

Press UP button on the test panel key pad until LCD reads "Passthru"

compat=0 (changes compat mode to passthru)

Using the test panel key pad navigate to the "Freq." screen

Press MENU/SEL and UP button simultaneously to change frequency to highest frequency. (pressing MUNU/SEL
and UP simultaneously will step the frequency up in increments of 16 only pressing the UP or DOWN buttons will
only increment by 1)

channel=XX

set channel (0(00) to 1020 (ff) in normal

tuning mode, 80 is 512)

Using the test panel key pad navigate to the "Gainsw" screen

select low gain

gainsw=2

Measure Noise (noise signal amplitude) at radio board J3

≤

-55 dBu

(-58)

Noise & microphonics measurements (high gain branch)

Prerequisite(s) Unit in set-up mode

Note

Entering Set-up mode is not necessary if the Alternate Method is exercised.

DUT in "Passthru"

No audio signal in at audio input rig

FREQ set to highest frequency

Gain set to "0"
Using the test panel key pad navigate to the "Gainsw" screen

select high gain

«
...
16
17
18
19
20
...
»

Содержание HH




























Отзывы:

Нет отзывов

Похожие инструкции для HH

Бренд: Samsung Страницы: 70

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 28

Бренд: Akura Страницы: 10

Бренд: Adonis Страницы: 4

Бренд: Audio Technica Страницы: 1

Бренд: Sennheiser Страницы: 4

Бренд: Vicon Страницы: 14

Бренд: QFX Страницы: 7

Бренд: Mark Страницы: 8

Dummy Head KU 100

Бренд: Neumann.Berlin Страницы: 20

Бренд: Mac Mah Страницы: 13

Бренд: Blue Microphones Страницы: 14

Бренд: Blaupunkt Страницы: 8

Бренд: Sound Projections Страницы: 2

2-661-374-11(4)

Бренд: Sony Страницы: 40

Бренд: Sony Страницы: 92

3-097-194-15(1)

Бренд: Sony Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды