Lectrosonics HH Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 27

background image

Remove DC voltage from Battery contacts and apply firmware version label to audio board

Test Segment 20 of 60

NOTE: This segment may be performed using one audio board to test multiple radio boards

Initial setup:



Known good, pre-tested audio board with PIC18F67J11
µC IC running firmware version appropriate & current for
part number connected to an untested radio board



Test panel key pad or appropriate test rig connected to
audio board J2



Apply +3.0VDC, 300mA current limit in at battery contact
J8 (J9 is circuit common).



All voltage measurements referenced to circuit common



All demodulated carrier and carrier deviation
measurements taken with a Hewlett Packard 8901B
modulation analyzer with no 8901B filters selected. Use of
other instruments may yield different results particularly
measurements pertaining to noise and phase and
measurements where noise is a significant factor



All audio stimulus signals applied to audio input rig
defined at foot of this document



All audio stimulus signals are single ended.



Carrier power for various part numbers are as follows:



HH=100mW, HHAU & HH/E01=50mW and HH/E02



All audio measurements taken with a

≤

10 Hz HPF and

80KHz LPF (use filter on audio signal analyzer, no
modulation analyzer unless otherwise specified).



This font indicates use of the

Alternate Method to manual testing. The
Alternate Method uses the LectroLink
apparatus and either the LecNet2

Command Terminal Utility or the
O:\ATE\MTE\HH\HH_LectroLink_Control.exe

program. Test steps bearing the same
number indicates alternate method(s).

Step

Measurement name & description

Measurement result (Typ)

Power Up sequence and current draw

Prerequisite(s): FPGA IC programmed

Hold test power button on test panel key pad for 3 seconds until DUT powers up

Observe behavior of test key pad LED

-10 LED turns on red, then -20 LED
turns on red then both off.

both LED's flash red once then

«
1
2
3
4
...
»

Содержание HH




























Отзывы:

Нет отзывов

Похожие инструкции для HH

Бренд: MAJORITY Страницы: 32

Бренд: Devine Страницы: 7

Бренд: Nady Systems Страницы: 2

Бренд: Audio Technica Страницы: 1

Бренд: Trevi Страницы: 46

Бренд: Austrian Audio Страницы: 2

Бренд: BEATFOXX Страницы: 16

Бренд: Shure Страницы: 14

Бренд: Bartlett Audio Страницы: 2

Бренд: Hannlomax Страницы: 2

Бренд: Linksys Страницы: 2

MHC-GX555 - Mini Hi Fi Component System

Бренд: Sony Страницы: 44

Бренд: Blaupunkt Страницы: 70

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 20

Бренд: Sony Страницы: 28

MHC-331 Primary

Бренд: Sony Страницы: 28

Бренд: Sony Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды