Lectrosonics HH Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 27

background image

tuning mode, 80 is 512)

Note:

BL944 specimens are permitted to exhibit 150% of otherwise allowable distortion. Some products have required this
additional margin. others have not. At the time of this writing, it is unknown how this product will shake out.
Momentarily connect Audio Board TP5 to TP22 (enter Set-up mode).
Entering Setup Mode is not necessary if the Alternate Method is used.

pilotbp=1

Using the test key pad navigate to the "DevOff" screen (Mid carrier frequency is highlighted)

tone=1 (sets DSP 1KHz test tone mode on)

Adjust RF Board R26 for minimum distortion at demodulated carrier at RF
Board J3.

≤

1.0% THD+N

(0.7)

Adjust RF Board R47 for 100KHz peak deviation at RF Board J3.

99 to 101KHz

(100)

Press MENU/SEL button on the test panel key pad (lowest carrier frequency is highlighted)

channel=XX

set channel (0(00) to 1020 (ff) in normal

tuning mode, 80 is 512)

Measure distortion at demodulated carrier at RF Board J3.

≤

1.2% THD+N

(0.7)

Press Up or Down button on test key pad for 100KHz peak deviation at RF
Board J3.

99 to 101KHz

(100)

devoff(0)? (Get deviation offset setting for the Low

channel) (+10 to -10). devoff(0)=x (set deviation
offset for 100KHz)(1KHz steps).

99 to 101KHz

(100)

Press MENU/SEL button on the test panel key pad (Highest carrier frequency is highlighted)

channel=XX

set channel (0(00) to 1020 (ff) in normal
tuning mode, 80 is 512)

Measure distortion at demodulated carrier at RF Board J3

≤

1.2% THD+N

(0.7)

Press Up or Down button on test key pad for 100KHz peak deviation at RF
Board J3.

99 to 101KHz

(100)

devoff(1)? (Get deviation offset setting for the High
channel) (+10 to -10). devoff(1)=x (set deviation

offset for 100KHz)(1KHz steps).

99 to 101KHz

(100)

«
...
14
15
16
17
18
...
»

Содержание HH




























Отзывы:

Нет отзывов

Похожие инструкции для HH

SuperStack 3 NBX

Бренд: 3Com Страницы: 496

Бренд: 3CX Страницы: 15

Controlled Magnetic 444D

Бренд: Shure Страницы: 5

Бренд: Immarsat Страницы: 2

Бренд: W Audio Страницы: 8

Бренд: LSS Страницы: 14

Бренд: Aiwa Страницы: 76

Бренд: Microtech Gefell Страницы: 18

Бренд: Sennheiser Страницы: 26

Бренд: ETS Страницы: 2

Бренд: Icom Страницы: 8

Бренд: Sennheiser Страницы: 10

Electret Series

Бренд: Pacific Antenna Страницы: 6

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 18

Бренд: RCA Страницы: 1

Бренд: RCA Страницы: 20

Бренд: RCA Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды