Lectrosonics HH Скачать руководство пользователя страница 21

Страница: 21 / 27

channel=xx,

set channel (0(00) to 1020 (ff)
in normal tuning mode, 80 is 512

≤

0.55% THD+N (0.35)

Limiter range adjust / and -10 Limiter light adjust

Prerequisite(s) Unit in set-up mode

Note

Entering Set-up mode is not necessary if the Alternate Method is exercised.

DUT in "Passthru"

FREQ set to middle

-30 dBu, 250Hz, low distortion, sinusoidal signal in at audio input rig

Using the test panel key pad navigate to the "Gain" screen

Press UP button to change audio level to "Gain 22 "

level=22 (changes audio level to 22)

(22)

Verify neither test key pad LED are red (limiter not activated)

Using the test panel key pad navigate to the "Limiter" screen (Ref is highlighted)

limitcal=1 (disables limiter calibration mode)

(0)

Measure and record audio signal amplitude at demodulated carrier RF J3

Reference for remainder of step

Press MENU/SEL button on the test panel key pad until (-5 XX is highlighted)

limitcal=2 sets limiter calibration mode to "calibrated drop"

(2)

Press UP or DWN button for 5 dB below reference amplitude in step 40.130.60 Reference value - (3.5

to 6.5) dB

(-5)

Adjust lscale for 5 dB below reference amplitude in

step 40.130.60 (lscale? gets setting) (lscale=xx sets
limiter scale setting,-16 to +15)

Reference value

- (3.5 to 6.5)
dB

(-5)

Press MENU/SEL button on the test panel key pad (2R XXXX is highlighted)

limitcal=0 (sets limiter calibration mode to "normal")

Increase stimulus signal amplitude in 1dB increments until D5 changes from green to red

ameter? (ameter? reading when D5 is green)

≤

17000

ameter? (ameter? reading when D5 changes to red)

≥

18000

ATS1 Audio Level

-29 to -26dBu (-27)

Содержание HH




























Результаты поиска

Содержание HH

Отзывы:

Похожие инструкции для HH

Бренды по названию

Популярные бренды

Lectrosonics HH, Процедура выравнивания

Результаты поиска

Содержание HH

Отзывы:

Похожие инструкции для HH

Бренды по названию

Популярные бренды