LAWO Crystal standard configuration Скачать руководство пользователя страница 97

Страница: 97 / 149

crystal standard configuration User Manual

Version: 6.4.0/4

97/149

8. Operation

8.10.5

Monitor Extension Options

The extensions offer additional monitor sources such as the HYBRIDs and CODECs. If a monitor source is
active, then its button lights in red.

MON CR Extension

MON STUDIO Extension

MON DJ Extension

MON GUEST Extension

Split Headphones

There is one additional option for MON DJ output called

SPLIT

When

SPLIT

is active (red), the DJ will hear different signals in the left and right ears of their headphones: left

ear = PFL (or CUE); right ear = the current monitor source (e.g. PGM 1).

You can use this mode to monitor the main program output while cueing up another source (pre-fader).

Содержание Crystal standard configuration






















































































































































Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды

LAWO Crystal standard configuration, Руководство пользователя

Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды